MNP/NONE is OK, MNP is the error correction. There is just no compression on
the link. DIRECT/NONE is another story. We just do what the client modem
asks us to. To force LAPM on these clients try:
3com &m5 ARQ mode
Lucent \n5 LAPM or disconnect
Rockwell \n5 LAPM or disconnect
These settings may vary from modem to modem. So remember to check the
manuals.
Thanks,
Josh Ebel - Beta Engineer
josh@ra.lucent.com
> -----Original Message-----
> From: Philip Kish [mailto:philip@ithink.com]
> Sent: Monday, June 07, 1999 2:18 PM
> To: Josh Ebel; Portmaster Modem List
> Subject: Re: (PMOD) CRC Error
>
>
> Is there a way to force a modem to use error correction? I get a few of
> these MNP/NONE and DIRECT/NONE and they always flood my PM3's with CRC
> errors.
>
> Thanks.
>
> Philip
>
> -
>
> --
>
> Philip Kish
> ~~~~~~~~~~~~~~~~~~~~~~~~~~~ http://www.ithink.net ~~~~~~~~~~
> iThink, Inc.
>
> (941) 299-6372
>
> For Support issues visit http://helpdesk.ithink.com
> ----- Original Message -----
> From: Josh Ebel <josh@livingston.com>
> To: Philip Kish <philip@ithink.com>; Portmaster Modem List
> <portmaster-modems@livingston.com>
> Sent: Monday, June 07, 1999 5:06 PM
> Subject: RE: (PMOD) CRC Error
>
>
> > Philip,
> >
> > This is a connect with no error correction. PPP has a built in
> CRC check.
> > The 0x51 debug shows the CRC failure.
> >
> > Josh Ebel - Beta Engineer
> > josh@ra.lucent.com
> >
> >
> > > -----Original Message-----
> > > From: owner-portmaster-modems@livingston.com
> > > [mailto:owner-portmaster-modems@livingston.com]On Behalf Of
> Philip Kish
> > > Sent: Monday, June 07, 1999 12:21 PM
> > > To: Portmaster Modem List
> > > Subject: (PMOD) CRC Error
> > >
> > >
> > > Hello,
> > >
> > > I am getting a user that whenever he connects to a PM3 gives
> me this in
> > > debug mode:
> > >
> > > (S18) PPP recv: BAD CRC - mdp M37
> > > (S18) PPP recv: BAD CRC - mdp M37
> > > (S18) PPP recv: BAD CRC - mdp M37
> > > (S18) PPP recv: BAD CRC - mdp M37
> > > (S18) PPP recv: BAD CRC - mdp M37
> > > (S18) PPP recv: BAD CRC - mdp M37
> > > (S18) PPP recv: BAD CRC - mdp M37
> > > (S18) PPP recv: BAD CRC - mdp M37
> > > (S18) PPP recv: BAD CRC - mdp M37
> > > ==================================
> > >
> > > When I do a show M37 I get this:
> > >
> > > sunset> show m37
> > > Card Type: LU1674 Chipset
> > > State: ACTIVE
> > > Active Port: S18
> > > Transmit Rate: 31200
> > > Receive Rate: 26400
> > > Connection Type: DIRECT/NONE
> > > Chars Sent: 152996931
> > > Chars Received: 13582921
> > > Retrains: 2
> > > Renegotiations: 1
> > > ==================================
> > >
> > > The noticeable thing I see in here is the DIRECT/NONE. Has anyone
> > > determined what causes this?
> > >
> > > The modem's ATI3 is as follows:
> > >
> > > SoftK56V_B2.1_V1.42
> > >
> > > According to Zoltrix this is a Cobra Modem. I noticed there were some
> > > drivers so I am trying them.
> > >
> > > If anyone else has encountered the DIRECT/NONE and knows how
> to fix it I
> > > would appreciate the info.
> > >
> > > Thanks.
> > >
> > > Philip
> > >
> > > -
> > >
> > > --
> > >
> > > Philip Kish
> > > ~~~~~~~~~~~~~~~~~~~~~~~~~~~ http://www.ithink.net ~~~~~~~~~~
> > > iThink, Inc.
> > >
> > > (941) 299-6372
> > >
> > > For Support issues visit http://helpdesk.ithink.com
> > >
> > > -
> > > To unsubscribe, email 'majordomo@livingston.com' with
> > > 'unsubscribe portmaster-modems' in the body of the message.
> > >
> >
>
>
-
To unsubscribe, email 'majordomo@livingston.com' with
'unsubscribe portmaster-modems' in the body of the message.