What OS are you running?
Dave Keal
SIERRA INTERNET
-------------------------------------------------------------------------------
On 16 May 1997, J. Patrick Bedell wrote:
> Hi everybody:
> I'm an ISP/portmaster newbie that has a PM3 plugged into 2
> channelized T-1 lines that are being turned up by Pac Bell. Right
> now, calls to the CT-1 phone # get a busy signal. (This busy signal
> has a shorter delay between tones than a "normal" busy signal.) What
> I'd really like to know is, what is the minimal set of configuration
> commands that need to be entered in order to get the digital modems to
> answer the incoming call?
> So far, I have set the two T-1 ports to "inband", with Pac
> Bell's specs ( ESF, B8ZS, wink start ). I've also put a DM-10 card
> into the PM3. The PM3 LEDs show that there is physical synchronizatin
> with the switch, but D channel signaling is not up (since we have
> inband signalling). Included below are the outputs from some show
> commands. As you can see, many things remain to be configured, but at
> this moment, I'm only interested in the ones that are directly
> relevant to the busy signal that I'm getting. Please let me knw if I
> should provide any more information. Thanks very much for any help
> that you can give. Pac Bell is waiting for this to be resolved, and
> it's quite an unpleasant role reversal for Pac Bell to be waiting on
> me :).
>
> J. Patrick Bedell
> jpbedell@alanine.com
>
>
> Command> version
> Livingston PortMaster PM-3 ComOS 3.5.1b8
> System uptime is 1 hours 54 minutes
>
> Command> show global
> System Name:
> Default Host: valine.alanine.com
> Alternate Hosts:
> IP Gateway: 207.212.234.1
> Gateway Metric: 1
> Default Routing: Quiet (Off)
> Name Service: DNS
> Name Server: valine.alanine.com
> Domain: alanine.com
> Telnet Access Port: 23
> Loghost: 0.0.0.0
> Maximum PMconsole: 1
> Assigned Address: 0.0.0.0
> RADIUS Server: 0.0.0.0
> Alternate Server: 0.0.0.0
> Accounting Server: 0.0.0.0
> Alt. Acct. Server: 0.0.0.0
> PPP Authentication: PAP: on CHAP: on
> ISDN Switch Type:
> End Point Disc: None
> Disabled Modules: SNMP OSPF
>
>
> Command> show all
> Local Addr: pm3.alanine.c (207.212.234.3) Default Host: valine.alanine.com
> Gateway: 207.212.234.1 Netmask: 255.255.255.0
> DNS Server: valine.alanine.com Domain: alanine.com
>
> Port Speed Mdm Host Type Status Input Output Pend
> ---- ----- --- ---------------- ------ ------------- ---------- ---------- ----
> C0 9600 off Login COMMAND 657 21270 2
> S0 64000 on Login/ IDLE 0 0 0
> S1 64000 on Login/ IDLE 0 0 0
> S2 64000 on Login/ IDLE 0 0 0
> S3 64000 on Login/ IDLE 0 0 0
> ... and so on, up to S47.
>
>
> Command> show modems
> Mdm Port Status Speed Compression Protocol Calls Retrain Disconnect
> --- ---- ------ ----- ----------- -------- ------ ------- ------------
> M0 READY UNKNWN NONE NONE 0 0 NORMAL
> M1 READY UNKNWN NONE NONE 0 0 NORMAL
> M2 READY UNKNWN NONE NONE 0 0 NORMAL
> M3 READY UNKNWN NONE NONE 0 0 NORMAL
> M4 READY UNKNWN NONE NONE 0 0 NORMAL
> M5 READY UNKNWN NONE NONE 0 0 NORMAL
> M6 READY UNKNWN NONE NONE 0 0 NORMAL
> M7 READY UNKNWN NONE NONE 0 0 NORMAL
> M8 READY UNKNWN NONE NONE 0 0 NORMAL
> M9 READY UNKNWN NONE NONE 0 0 NORMAL
>
> Command> show sessions
> Port User Host/Inet/Dest Type Dir Status Start Idle
> ---- --------------- ---------------- ------- --- ------------- ------ ------
> C0 !root - Login In COMMAND 0 0
> S0 - - Log/Net In IDLE 0 0
> S1 - - Log/Net In IDLE 0 0
> S2 - - Log/Net In IDLE 0 0
> S3 - - Log/Net In IDLE 0 0
> ... continued to S47
>
> Command> show S0
> --------------------- Current Status - ISDN Port S0 ------------------------
> Status: IDLE
> Input: 0 Abort Errors: 0
> Output: 0 CRC Errors: 0
> Pending: 0 Overrun Errors: 0
> TX Errors: 0 Frame Errors: 0
> Modem Status: DCD- CTS- TELCO+ Disconnect:
>
> Active Configuration Default Configuration (* = Host
> -------------------- --------------------- Can Override)
> Port Type: Login/Netwrk Login/Netwrk (Dial In & Out) (Security)
> Login Service: PortMaster PortMaster
> Line Speed: 64000 64000
> Hosts: default
>
> Terminal Type:
> Login Prompt: $hostname login:
> Directory No:
> Dial Group: 0
>
> Command> show m0
> State: READY
> Chars Sent: 0
> Chars Received: 0
> Retrains: 0
> Renegotiations: 0
>
> Total Calls: 0
> Modem Detects: 0
> Good Connects: 0
>
> Connection Failures
> No Modulation: 0
> No Protocol: 0
> Not Operational: 0
> Total Failed: 0
>
> Session Terminations
> Lost Carrier: 0
> Normal Disconnect: 0
>
>
> Command> show line0
> ---------------------- line0 - T1 Inband DS0 ---------------
>
> Status: UP Framing: ESF Encoding: B8ZS PCM: u-law
>
> Signaling: Trunk E&M wink start
>
> Receive Level: +2dB to -7.5dB
>
> Alarms Violations
> ----------------------------- -----------------------------
> Blue 0 Bipolar 0
> Yellow 0 CRC Errors 0
> Receive Carrier Loss 0 Multiframe Sync 0
> Loss of Sync 0
>
> ("show line1" gives identical output)
>