In this example we like to connect one branch (office 1) with 4 PC, novell
4.1 and 1router but without novell server to a second branch (office 2)
with 5 PC, and another office portmaster router. The protocol will be IPX
>
>The connection will be done with ISDN. We like to use only 1 B channel, not
both. The second will be available to connect to us, to the banks, ...
>
>
>Here is a picture of the connection we like to do
>
>
>office 1(it has NOT netware Novell server) =20
> PC PC =20
> | | IPX: 0000A002
>-----------------------------------
> |
> OR-ST
> |
> | IPX: 000000F3
> |
> |
> OR-ST
> | IPX: 0000B002
>------------------------------------
> | | |
> PC PC novell =20
> server
> 4.1
>office 2 (It has the novell server)
>
>
>
>
>
>CONFIGURATION
>+++++++++++++++++++++++++++++++++++++++++++++++++++++++
>office 1=20
>+++++++++++++++++++++++++++++++++++++++++++++++++++++++
>global parameters:
> name of router office1 =09
> IP address 10.127.0.1=09
> netmask 255.255.255.0 =09
> default route ????
> IPX network 0000A002=09
> IPX frame type 802.2
> isdn switch NET3
>
>ethernet port parameters
> protocol IP/IPX
> IP address 10.127.0.1=09
> netmask 255.255.255.0 =20
> IPX network 0000A002 =20
> IPX frame type 802.2
> Broacast addres 10.127.0.254 =20
> routing quiet=20
> ethernet enabled
>
>
>ISDN port parameters
> port type network
> network type dial-out
> dial group 0
> spid 2
> directory no. 2
>
>
>dial location table
> location name office2
> type on-demand
> protocol PPP (or PPP/IP/IPX ??)
> IP destination 194.224.0.11
> IPX network 0000F3
> routing quiet
> MTU 1500
> compression ON
> Idle timeout 3
> maximum port 1
> high water 0
> dial group 0
> dial script V25
> send/expect CRN+3443666001
> =3DDCD=3D=20
>
>
>
>+++++++++++++++++++++++++++++++++++++++++++++++++++++++++
>office 2
>+++++++++++++++++++++++++++++++++++++++++++++++++++++++++
>global parameters:
> name of router office2
> IP address 194.224.0.11=09
> netmask 255.255.255.192
> default route ????
> IPX network 0000B002
> IPX frame type 802.2
> isdn switch NET3
>
>ethernet port parameters
> protocol IP/IPX
> IP address 194.224.0.11
> netmask 255.255.255.192
> IPX network 0000B002
> IPX frame type 802.2
> Broacast address 194.224.0.63 =20
> routing quiet ???)
> ethernet enabled
>
>
>ISDN port parameters
> port type network
> network type dial-in/dial-out
> dial group 0
> spid 1
> directory no. 1
>
>
>dial location table (an example)
> location name sylvain.bessaye
> type on-demand
> protocol PPP (or PPP/IP/IPX ??)
> IP destination 194.51.94.136
> IPX network 0000F3?
> routing quiet
> MTU 1500
> compression ON
> Idle timeout 3
> maximum port 1
> high water 0
> dial group 0
> dial script V25
> send/expect CRN073372670130
> =3DDCD=3D=20
>
>dial-in user table
> username office1
> password what you like
> type network user/normal
> protocol PPP/IP/IPX=20
> user IP address 10.127.0.1specified=20
> netmask 255.255.255.0
> IPX network 000000F3=20
> routing quiet
> MTU 1500
> compression ON
>
>
>As you see we want that a PC of office1 can connect to the Novel server
>that is in the office2. So attaches it.
Is it possible that when we start a PC (office1) and load the novell drivers
to attch to the Novell server that is in the other network?. To do this the
portmaster will detect that a PC are sending pakets to a server that is not
in this network, so it will call to a appropiate ISDN number (office2 ), the
office2 router will answer and will let connect to the server.
>questions
>0- Is it all the configuration right?
>1-is convenient to set routing to quiet ? we don=B4t like to use it because=
our
connections will be static
>
>2- who must define the IPX and IP gateway and which values
I see that because in a example in the book it defines the IP gateway like
the IP of the router.
>3- in IP is not necessary to define the IP network between the routers. In=
IPX
seems to be the opposite. In this example 0000F3. Is it necessary?=20
>if we have a PM2 with N connections from remote IPX networks, the IPX
network of the serial line is always the same (000000F3 in the example of
the book) or different (one for every remote connections)
>4-In the location table :
Script :expect =3DDCD=3D : in spain too ??
>is better to define At commnads Asyncro or V25 commands?
>which is faster connecting ?
>
>
>
>5- the password that you ask a user in our router must be the same as=
your
routers's password ?
>
>6- which is the meaning of default route ?
>and it values ?
>
Thank you very much for all your help and time.
Very Sincerely,
Feranando Martin
Interlinea2000 & Urdanibia2
http://www.i2000.es
voz: 943-619101
Fax: 943-618159