The Portmaster is PM2e30
Few things people will need to try to help you:
Q >> What the user entry looks like in the user table?
Command> show user crc
Username: crc Type: Dial-in Network User
Address: 192.168.3.49 Netmask: 255.255.255.0
Protocol: PPP Options: Quiet, Listen, Compression
MTU: 1500 Async Map: 00000000
Command>
Q >> How are you authentication the user when you do not use the user table?
I m using RadiusNT with MSSql 6.5 as a backend data base.
Q >> What does the route table look like with out the user logged on and after the user logs on both ways?
the ipaddress shown below "192.168.3.49" is the user "crc" connected, authenticated by user table and facing a problem.
(No browsing, no ping , no telnet where continous CRC errors/sec with beep if enabled in NT 4.0 may be due to broadcasts on network.)
Other ipaddresses show other users running fine.
Command> show route
Destination Mask Gateway Source Flag Met Interface
----------------- ---- -------------------- ------- ---- --- ---------
0.0.0.0 0 192.168.3.1 local NS 1 ether0
192.168.3.102 32 192.168.3.102 local HL O 16 Unknown
1 ptp21
192.168.3.115 32 192.168.3.115 local HL 1 ptp0
192.168.3.49 32 192.168.3.49 local HL 1 ptp5
192.168.3.108 32 192.168.3.108 local HL 1 ptp6
Q >> What does the port settings look like when the user is logged on both ways?
Command> show S5
Current Status - Port S5
Status: ESTABLISHED
Input: 1509893 Parity Errors: 0
Output: 9386480 Framing Errors: 0
Pending: 0 Overrun Errors: 0
Modem Status: DCD+ CTS+
Active Configuration Default Configuration
Port Type: Netwrk Login/Netwrk (Dial In) (Security)
Baud Rates: 115200 115200,115200,115200
Flow Control: RTS/CTS RTS/CTS
Modem Control: on on
Remote Host: 192.168.3.49
Netmask: 255.255.255.255 0.0.0.0
Interface: ptp5 (PPP,Listen,VJ-Comp)
Mtu: 1500 1500
Async Map: L:00000000 R:00000000 00000000
Dial Group: 0
Login Message: 2105
Command>
Q >> What does the port settings look like when the user is not logged on?
The same port when no one is connected on that port
Command> show S5
Current Status - Port S5
Status: IDLE
Input: 1510111 Parity Errors: 0
Output: 9394616 Framing Errors: 0
Pending: 0 Overrun Errors: 0
Modem Status: DCD- CTS+
Active Configuration Default Configuration
Port Type: Login/Netwrk Login/Netwrk (Dial In) (Security)
Baud Rates: 115200 115200,115200,115200
Parity: none none
Flow Control: RTS/CTS RTS/CTS
Modem Control: on on
Terminal Type:
Dial Group: 0
Login Message: 2105
Command>
Q >> What type of modem on both ends?
at server end : Compaq Microcom 4000 (Quad 33.6k Analogue)
Q >> What type of client?
Windows NT 4.0, windows 95
Shoaib
-
To unsubscribe, email 'majordomo@livingston.com' with
'unsubscribe portmaster-users' in the body of the message.
Searchable list archive: <URL:http://www.livingston.com/Tech/archive/>