RE: (PM) Pipeline 75 dialling into PM3/CT1 (fwd)

James Courtier-Dutton (dutton@livingston-ent.co.uk)
Sat, 17 Apr 1999 15:38:58 +0100

Hello
As you are trying DOV. Your Voice channel seems to be getting corrupted.
I would leave the data service to whatever you had for the PM2 and see what
happens.
This might not work as the PM2 connection might have been ISDN and the PM3
is doing CT1.
Cheers
James

> -----Original Message-----
> From: owner-portmaster-users@livingston.com
> [mailto:owner-portmaster-users@livingston.com]On Behalf Of Dan Machesky
> Sent: Saturday, April 17, 1999 11:03
> To: portmaster-users@livingston.com
> Subject: Re: (PM) Pipeline 75 dialing into PM3/CT1 (fwd)
>
>
> > I think there is a fundamental communications gap here. Note
> that the PM
> > keeps receiving the SAME request, over and over. We never once
> recieve an
> > ACK or a NAK despite all of the requests we've sent. And,
> we've ACK'd the
> > request each time, yet the Pipeline keeps making it.
> >
> > It seems that the Pipeline is not seeing anything from the PM. The PM
> > is seeing it - but not the other way around. If you can I'd do
> a debug on
> > the Pipeline to see what, if anything, it is receiving back.
> >
> > >Received LCP_CONFIGURE_REQUEST on port S35 of 17 bytes containing:
> > >Received LCP_CONFIGURE_REQUEST on port S35 of 17 bytes containing:
> > >Sending LCP_CONFIGURE_REQUEST to port S35 of 18 bytes containing:
> > >Sending LCP_CONFIGURE_ACK to port S35 of 21 bytes containing:
>
> Here is a debug from the Ascend pipeline.
> -------------snip--------------
> WANDATA: looking for session
> profile 0, name pm3, ip 198.xx.xx.xx, ether<none>, outdial
> <none>
> startSession pm3 newSession pm3
> WANDATA-0: profile 1, 'pm3' assigned WANDATA-0: >> RouteID 0, state
> INACTIVE, event OPEN_OUT_REQ WANDATA-5: attempting to place call to
> '920xxxx' WANDATA-5: << RouteID 0, state CALLING
> WAN-16: wanOpenOriginate(callID 16)
> WANDATA: Call state change, port 8, connected 1, carrier 0
> WANDATA-5: WAN state change, route 16
> WANDATA-5: >> RouteID 16, state CALLING, event CALL_CONNECTED
> WANDATA: EVENT IGNORED
> WANDATA-5: << RouteID 16, state CALLING
> WANDATA: Call state change, port 8, connected 1, carrier 1
> WANDATA-5: WAN state change, route 16
> WANDATA-5: >> RouteID 16, state CALLING, event CARRIER_EST
> WAN-16: wanRegisterData, I/F 5
> WAN-16: wanRegisterData, I/F 5, clearing stats
> PPP-OUT-5 (off 0x0):(task: 250290, time: 27041.86) 29 octets @ 2C525A
> [0000]: FF 03 C0 21 01 02 00 19 00 04 00 00 01 04 05 F4
> [0010]: 11 04 05 F4 13 09 03 00 C0 7B 72 D2 70
> WANDATA-5: << RouteID 16, state OPENING
>
> WAN-16: Bad CRC, frame ignored
> WAN-16: Bad CRC, frame ignored
> ** message repeated 50 times **
> ** OUCH!! Is this a 3.8.2 problem?
>
> ----- data lost -----
> WAN-16: Bad CRC, frame ignored
> ----- data lost -----
> ** message repeated 50 times **
>
> WAN-16: Bad CRC, frame ignored
> PPP-OUT-5 (off 0x0):(task: 250290, time: 27045.77) 29 octets @ 2C791A
> [0000]: FF 03 C0 21 01 02 00 19 00 04 00 00 01 04 05 F4
> [0010]: 11 04 05 F4 13 09 03 00 C0 7B 72 D2 70
> PPP-OUT-5 (off 0x0):(task: 250290, time: 27049.81) 29 octets @ 2C809A
> [0000]: FF 03 C0 21 01 02 00 19 00 04 00 00 01 04 05 F4
> [0010]: 11 04 05 F4 13 09 03 00 C0 7B 72 D2 70
> PPP-OUT-5 (off 0x0):(task: 250290, time: 27053.85) 29 octets @ 2C525A
> [0000]: FF 03 C0 21 01 02 00 19 00 04 00 00 01 04 05 F4
> [0010]: 11 04 05 F4 13 09 03 00 C0 7B 72 D2 70
> WAN-16: wanCloseSession, I/F 5; hdlc 22C398; pend 0
> WANDATA: Call state change, port 8, connected 0, carrier 0
> WANDATA: Unable to add call block entry, 0 setting found
> WANDATA-5: WAN state change, route 16
> WANDATA-5: >> RouteID 16, state OPENING, event CALL_DISCONNECTED
> WANDATA-5: closing encaps for 198.88.0.66
> WANDATA-5: ENCAPS state change, route 16
> WANDATA-5: << RouteID 16, state DOWN
> WANDATA-5: WAN state change, route 16
> WANDATA-5: >> RouteID 16, state DOWN, event ENCAPS_CLOSED
> WANDATA-0: << RouteID 16, state DESTROYED
> --------snip-----------
>
> I am running 3.8.2 on the PM3, and have tried everything from 5.1 to
> 6.1.42 on 2 p75's and 1 p130, with the same results. The configs on
> the pipelines work fine when dialing into a pm2. The only difference
> being that I chaged the data srv to "voice", and changed the "rem
> addr" and "rem name" to reflect calling into the pm3.
>
> Sincerely,
> Dan Machesky
> dan@beesky.com
> -
> To unsubscribe, email 'majordomo@livingston.com' with
> 'unsubscribe portmaster-users' in the body of the message.
> Searchable list archive: <URL:http://www.livingston.com/Tech/archive/>
>

-
To unsubscribe, email 'majordomo@livingston.com' with
'unsubscribe portmaster-users' in the body of the message.
Searchable list archive: <URL:http://www.livingston.com/Tech/archive/>