[Top] [Prev] [Next] [Bottom]
-
10Base2 port 2-9
-
10BaseT port 2-7
-
airflow and cooling 2-2
-
applying power 2-11
-
AUI port 2-8
-
BNC port 2-9
-
boot
-
failure A-5
-
sequence A-4
-
boot messages on the console
-
checking A-4
-
interpreting A-5
-
cables
-
Ethernet B-5
-
null modem pinout B-2
-
specifications B-1
-
straight-through pinout B-3
-
T1/E1 B-4
-
caution icon ix
-
channelized T1
-
line connection 2-6
-
ports 1-6
-
service 1-1
-
support 1-6
-
chassis accessibility 2-2
-
command line interface 1-7
-
ComOS software 1-7
-
console mode diagnostic messages A-5
-
console port, connecting a console 2-5
-
contact information
-
Europe, Middle East, and Africa x
-
Lucent Remote Access technical support x
-
mailing lists xi
-
North America, Latin America, and Asia Pacific x
-
technical support ix
-
conventions in this guide viii
-
cooling and airflow 2-2
-
DB-15 female connector 2-8
-
digital modem cards
-
installation 3-1
-
location 3-1
-
model numbers 1-7
-
removing 3-3
-
DIP switch
-
location 1-5
-
position for console use 2-5
-
position for Ethernet 10Base2 connection 2-9
-
position for Ethernet 10BaseT connection 2-7
-
position for Ethernet AUI connection 2-8
-
position for external modem installation 3-4
-
DIP switches 1-2
-
document advisory ix
-
document conventions viii
-
documentation, related vii
-
E1 line
-
connecting 2-6
-
for ISDN PRI 1-1
-
pinout specifications B-4
-
support 1-6
-
See also T1/E1 ports
-
electrical specifications C-2
-
environmental requirements 2-2
-
environmental specifications C-2
-
equipment required 2-3
-
Ethernet cable, connecting
-
10Base2 2-9
-
10BaseT 2-7
-
AUI 2-8
-
LED verifying 2-12
-
specifications B-5
-
Ethernet interface B-5
-
Ethernet ports
-
location 1-5
-
number by model 1-6
-
external modem
-
cable B-3
-
installation 3-4
-
FAULT LED 2-11
-
fractional T1 1-1
-
front panel 1-2
-
fuse, replacing A-7
-
grounding requirement for Ethernet 10Base2 port 2-9
-
installation
-
accelerator card 3-9
-
checklist 2-1
-
compression card 3-9
-
digital modem cards 3-1
-
external modem 3-4
-
fuse A-7
-
memory 3-5
-
T1 card 3-7
-
interface specifications C-1
-
IP address, setting 2-13
-
IPX address, setting 2-14
-
ISDN PRI
-
line connection 2-6
-
ports 1-6
-
service 1-1
-
support 1-6
-
LED behavior
-
observing for troubleshooting A-1
-
verifying 2-11
-
LEDs 1-3
-
login
-
password 2-13
-
procedure 2-13
-
mailing lists, subscribing to xi
-
memory
-
adding memory 3-5
-
specifications 3-5
-
messages on the console
-
checking A-4
-
interpreting A-5
-
network address
-
IP 2-13
-
IPX 2-14
-
network connections
-
Ethernet 10Base2 2-9
-
Ethernet 10BaseT 2-7
-
Ethernet AUI 2-8
-
T1/E1 2-6
-
note icon ix
-
null modem cable
-
pinout specifications B-2
-
use B-1
-
overview of PortMaster 3 1-1
-
panel
-
front 1-2
-
rear 1-5
-
password 2-13
-
PC settings for console use 2-5
-
pinouts
-
null modem cable B-2
-
straight-through cable B-3
-
PM-3A-1E 1-6
-
PM-3A-1T 1-6
-
PM-3A-2E 1-7
-
PM-3A-2T 1-6
-
PM-3D-1E 1-6
-
PM-3D-1T 1-6
-
PM-3D-2E 1-7
-
PM-3D-2T 1-6
-
PortMaster 3
-
overview 1-1
-
product line 1-6
-
software 1-7
-
ports
-
Ethernet 10Base2 2-9
-
Ethernet 10BaseT 2-7
-
Ethernet AUI 2-8
-
T1/E1 2-6
-
power
-
applying 2-11
-
guidelines 2-2
-
PRI. See ISDN PRI
-
Primary Rate Interface. See ISDN PRI
-
product line, PortMaster 3 1-6
-
rack installation 2-4
-
rear panel 1-5
-
DIP switches 1-2
-
related documentation vii
-
removing digital modem cards 3-3
-
replacing fuse A-7
-
RJ-48C connector
-
for Ethernet 10BaseT port 2-7
-
for T1/E1 ports 2-6
-
specifications B-4
-
safety recommendations 2-3
-
SIMM
-
installing 3-5
-
specifications 3-5
-
single inline memory module. See SIMM
-
site requirements
-
air flow and cooling 2-2
-
chassis accessibility 2-2
-
environment 2-2
-
power guidelines 2-2
-
software, PortMaster 3 1-7
-
specifications
-
cabling B-1
-
electrical C-2
-
environmental C-2
-
interface C-1
-
SIMM 3-5
-
size and weight C-2
-
straight-through cable
-
pinout specifications B-3
-
use B-1
-
support, technical ix, x
-
T1 lines
-
connecting 2-6
-
for channelized T1 1-1
-
specifications B-4
-
support 1-6
-
T1/E1 ports
-
location 1-5
-
number by model 1-6
-
technical support ix
-
temperature 2-2
-
terminal settings for console use 2-5
-
thin Ethernet. See 10Base2 port 2-5
-
troubleshooting A-1
-
VDC lines 2-10
-
warning icon ix
-
weight specifications C-2
-
work area
-
required equipment 2-3
-
safety recommendations 2-3
[Top] [Prev] [Next] [Bottom]
spider@livingston.com
Copyright © 1998, Lucent Technologies. All rights
reserved.